Open the cover to the pilot (if one is present) and look inside the opening with the help of a flashlight. Your gas release or electric heating element is malfunctioning.
First locate the temperature controls.
How to turn off gas water heater pilot light. Remove the burner access covers and unscrew the nuts on the gas, pilot and thermocouple lines. The thermocouple is a device on the gas heater that senses the pilot’s heat and feeds it gas. If there is no release of any combustion agent, the pilot light will fail to start.
The pilot light is the small flame fueled and lit by a gas burner at the base of your water heater. The pilot light will be cut if it’s malfunctioning because then it will cut the gas to the pilot. The guaranteed issue will be that your water heater will take a long time to heat the tank water back up.
Some water heaters just have an open gap instead where you can see the pilot light burner. A handle parallel to the pipe indicates an open valve. Turn the dial past the pilot position to the off position.
Here are some critical reasons why. Generally leaving your water heater system on a pilot mode even for 3 weeks will not cause leakage. When the flame ignites, continue to hold the gas knob or button down for a full minute.
Steps to relight the pilot light. It is common on fireplaces and older/cheaper furnaces and water heaters. Hold a lighted match to the pilot — a long fireplace match.
If you have trouble locating it, it’s usually located at the front of the water heater. Open the door/cover over the pilot light access. Make sure to remove out the outer and the inner panel to access out the light of the panel.
Dirty or dusty pilot light burner. Turn the knob to “off,” and then wait five minutes for the gas to clear before you follow these steps: Check to make sure that the water heater has turned off.
Use a flashlight or a headlamp to find the burner inside. Push down the red button to the left of the gas knob. Gas water heaters need to have a flow of gas to the pilot light in order to remain working.
This is where we can move on and check the interior door panel for the directions to find out how to turn on gas water heater pilot light. Shut off the gas valve. Pull out the water heater pilot light burner.
Open the door/cover over the pilot light access. Make sure to turn the thermostat to the lowest setting. There are timers that automatically turn on/off the water heater depending on the need at hand.
Reset the thermostat so it is on the lowest setting possible. A pilot light is always burning while using a small amount of gas, either a water heater is running or not. This will start the flow of gas to the pilot.
Hold down the pilot button or the ignite button. Turn out the on/off switch of the pilot towards a pilot’s position. Make sure the line valves are open.
Find the pilot light access. This shuts off the pilot as well as preventing the burner from igniting. If the gas supply is blocked, or if the amount of gas isn’t sufficient, the pilot light won’t stay lit.
Hold the pilot’s button and then make sure to use the long lighter or a match to ignite the flame. If you only want to turn off the heater for a few minutes for servicing, turn the dial to pilot. Typically, this will be under the gas valve.
Some units, there will be difficulties to turn it on again, lighting a pilot light comes to mind for gas powered water heaters. If you find your water not warm enough while on a pilot mode, then there will be a problem with your system. You may hear a slight hiss.
Turn the gas knob to “pilot,” press and hold it down. How to light a water heater pilot light. We want to put the heat to the minimum.
When the thermocouple is functioning properly, the gas is cut off on its own. Turn the switch for the pilot light so it is on the pilot position. This gas flame heats up the metal pipe inside your water heater which heats up your water, but like any common lighter or grill igniter, you need both flame and gas for the light to stay lit.
Hold the red button down while pressing the piezo ignitor striker, found to the immediate right of the gas knob, repeatedly until the pilot is lit. Now off the regulator valve. Turn off the control valve.
The knob should be clearly labelled. The pilot light starts after the igniter sparks, which causes this flame to activate the water heater. As we’ve mentioned before, pilot light is a necessary part of a gas water heater.
The pilot mode can help you to detect if there is any leakage of gas in your system. Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it’s burning properly. No, you should not turn off your water heater when on vacation.
This will be located under the gas valve; This is the only way to make sure the gas is reaching the pilot light. Take the panels of the water heater so you can reach the pilot light wherever it is located.
If it senses that the pilot light has gone out, the thermocouple shuts off the gas supply to the flame in order to prevent safety issues with your water heater. The short and sweet answer: Also, is it dangerous if the pilot light goes out on water heater?
Turn the gas control knob to pilot and press it downward. A pilot light is a small device that is designed to provide the flame and light the gas coming out of the gas valve and main burner. While still holding the gas down, light that pilot.